NT5B50 Norstar 0 x 16 Copper Station Module

This is the 16 station expansion module for the M824 control unit. It plugs into an expansion port on the NS2PRT-CP-EXP-R or the NS6PRT-CP-EXP-R expansion cards..

NTBB41  Norstar 0 x 16 Fiber Station Module

This is the 16 station expansion module for the MICS Norstar System. It connects to the MICS control unit via a fiber connection on the 2 port or 6 port fiber expansion card. Up to 16 additional telephones can be added to the system per 0 X 16 added.

NTBB51 Norstar 0 x 8 Analog Station Module ASM

This is an analog station module that allow up to 8 analog port to be added to the MICS Norstar System. It connects via an expansion port on either the 2 port or 6 port expansion card. One additional M0X8 analog module can be added by daisy chaining from the first module, thus leaving your expansion ports available for other uses.  Caller ID Add $100

NT5B32 Norstar 12 x 0 Copper Trunk Module,

This module allow for the addition of trunk lines to the M824 Norstar control unit. It connects via an expansion port on the 2 port or 6 port copper expansion cards. This module houses 3 NT5B40GA cards to allow up 12 trunks to be added to the system..

NTBB20 Norstar 12 x 0 Fiber Trunk Module

This module allow for the addition of trunk lines to the MICS Norstar control unit. It connects via an expansion port on the 2 port or 6 port fiber expansion cards. This module houses 3 NT5B40, NT7B75, or NT5B37 (DID) cards to allow up 12 trunks to be added to the system.

NT5B38 Norstar 4 X 0 E&M DISA Cartridge

Provides two - 4 wire E&M/ Tie line trunks between two systems. Provides 2 - 4 wire auto answer direct inward system access lines.

NT5B40 Norstar 4 CO Copper Trunk Cartridge

This is the standard trunk card for the M824 control unit line expansion. It is housed in an 12 X 0 copper trunk module and allows for the addition of up 4 trunks lines..

NT5B41 Norstar 4 CO Trunk Cartridge Caller ID
 

This is the caller ID card for the MICS control unit and/or the 12 X 0 fiber trunk module used to expand the line capability of the MICS. You must have these cards in order to receive caller ID from your dial tone provider. This card can also be modified to work with the M824 Norstar control unit.

NT7B74 Norstar T-1/PRI Cartridge

This card allows for the direct connection of a T1 digital trunk line. This will allow the connection of up 24 lines on one connection. You must have either a T1 clock card or the 6 port fiber combo card, which has T1 clocking built into an expansion card.

NT7B75 Norstar 4 CO Fiber Trunk Cartridge

This is the standard fiber trunk card for the MICS 0X32 control unit. It is capable of up to 4 lines per card. The main control unit will support 2 trunk cards but must have the M12X0 to expand beyond 8, unless T1 is used.

NTBB04 Norstar CICS 8 Station Expansion Cartridge

NTBB04 Norstar CICS 8 Station Expansion Cartridge.

NT5B26 Norstar 2-Port Copper Expansion Cartridge

This expansion card was designed for the M824 Control Unit to add expansion modules. There are two ports which can be used to add either the M12X0 copper trunk module or the M0X16 copper station module. If 2 ports is not enough expansion, check out the 6 port copper expansion.

NTBB02 Norstar 2 Port Fiber Expansion Cartridge
 

This expansion card was designed for the M824 Control Unit to add expansion modules. There are two ports which can be used to add either the M12X0 copper trunk module or the M0X16 copper station module. If 2 ports is not enough expansion, check out the 6 port copper expansion

NT5B27 Norstar 6-port Copper Expansion Card

This is the 6 port expansion card used inside of the Norstar M824 KSU and allows for up to six expansion modules (M12X0 copper trunk module or M0X16 copper station module) to be added to the control unit. This card provides maximum expansion capabilities on the M824.

Routes calls from the public network directly to Norstar sets, bypassing an attendant, reducing traffic to the central answering position.

Compatible with the Modular ICS Fiber Trunk Module and the Modular 8x24 Copper Trunk Module.

All DID trunk cartridges have disconnect supervision.

DID trunking is supported on the Modular 8x24 and Modular ICS (MICS) systems but not supported on the 3x8 or CICS system.

This is the 6 port fiber expansion card for the MICS. It allows the expansion of lines and/or stations via the M12X0 fiber trunk module or the M0x16 fiber station module. The MICS control unit will support up to 2 T-1 for Digital Trunk connection, and this card has the T-1 clock card built in. By adding this card you are gaining not only six ports of expansion but also hardware necessary for adding a T-1.

NTBB24 Norstar T1 Services Clock Cartridge

This card is used in conjunction with the NT7B74 T1 digital trunk card. It is required in order to time the channels on T1. You may also use the 6 port fiber combo card to get the clocking feature and expansion ports.

ATA II Norstar  Analog Terminal Adapter

The Norstar ATAII analog terminal adapter is a device that allows you to convert a digital port on the Norstar system into an analog port. The ATAII is the preferred model of analog terminal adapters for the MICS and CICS control units. Examples of it use would be for adding an analog cordless telephone, an answering machine or any other analog device to the Norstar system

Norstar  Caller ID Interface (CII) for 824

The Norstar Caller ID Interface (CII) was designed to add Caller ID Feature to the Norstar  824 KSU.

Norstar  MICS POWER SUPPLY